SMD EMI Filters Common Mode Choke

Common Mode SMD EMI Filters Choke

TCPWC

Features

Highly Effective in Noise Suppression.
Almost No Distortion on High Speed Signal.
Low Differential-Mode Impedance with High Coupling Factor.
Small Chip Inductor with Ferrite Core and Two Line Types Wire wound.
High Impedance at Noise Band and Low Differential-Mode Impedance at Signal Band.

Applications

USB Line for Personal Computers and Peripheral.
IEEE 1394 Line for Personal Computers ,DVC,STB.
LCD Panels. Low-Voltage Differential Signal (LVDS).
EMI Radiation Noise Suppression for Any Electronic Device.

The EMI Filter TCPWC Coils are lead-free and RoHS compliant. Please contact us for details with your specific needs.

EMI Filter TCPWC - Dimensions (unit: mm)

SMD EMI Filters Common Mode Choke Configurations

SMD EMI Filters Common Mode Choke Dimensions

TYPE	A	B	C	E	F	G	H	I	J	K
TCPWCH05	2.0±0.2	1.2±0.2	1.2±0.2	0.45	1.2	0.4	0.8	0.4	0.4	0.90
TCPWCH06	3.2±0.2	1.6±0.2	1.8±0.2	0.60	2.0	0.6	1.6	0.6	0.4	1.05

Electrical Characteristics for TCPWC EMI Filter

Part Number	Impedance (Ω) @100MHz	DCR (Ω)(max)	Rated Current (mA)(max)	Rated Voltage (V)(DC)	Withstanding Voltage (V)(DC)	Insulation Resistance (MΩ)(min)
TCPWCH05MT670	67	0.25	400	50	125	10
TCPWCH05MT900	90	0.35	330	50	125	10
TCPWCH05MT121	120	0.30	370	50	125	10
TCPWCH05MT181	180	0.35	330	50	125	10
TCPWCH05MT201	200	0.35	330	50	125	10
TCPWCH05MT261	260	0.40	300	50	125	10
TCPWCH05MT371	370	0.40	280	50	125	10

TCPWCH06MT900	90	0.30	370	50	125	10
TCPWCH06MT161	160	0.40	340	50	125	10
TCPWCH06MT261	260	0.50	310	50	125	10
TCPWCH06MT601	600	0.80	260	50	125	10
TCPWCH06MT102	1000	1.00	230	50	125	10
TCPWCH06MT222	2200	1.20	200	50	125	10

Operating Temp.: -40°C+85°C.

Packaging Quantity & Reel Specifications (Unit: mm)

Packaging Quantity Reel Specifications - EMI Filter TCPWC

Type	Emboss Plastic Tape (PCS)
TCPWCH05	2000
TCPWCH06	2000

Emboss Plastic Tape Specifications (Unit: mm)

Emboss Plastic Tape Specifications - EMI Filter TCPWC

Codes	A ±0.10	B ±0.05	W ±0.20	E ±0.10	F ±0.10	P0 ±0.10	P1 ±0.10	P2 ±0.10	ΦD0 +0.10	t ±0.10
TCPWCH05	1.40	2.55	8.0	1.75	3.5	4.00	4.00	2.00	1.50	1.35
TCPWCH06	1.90	3.50	8.0	1.75	3.5	4.00	4.00	2.00	1.50	2.10

Leader / Tape

Peel-off Force

The force for tearing off cover tape is 0.05 ~ 0.69(N) in the arrow direction at the following conditions:
Temperature: 5 ~ 35°C, Humidity: 45 ~ 85%, Atmospheric pressure: 860 ~ 1060 hpa

EMI Filter TCPWC - Electrical Performance Test

Test Items	Specifications	Test Conditions / Test Methods
Impedance	Refer to standard electrical characteristic spec.	LCR Meter HP 4291B
DC Resistance (RDC)	Refer to standard electrical characteristic spec.	Micro-Ohm meter (GOM-801G)
Withstand Voltage (VDC)	Component should not be damaged	Test Voltage: 2.5 Times Rated Voltage Testing Time: 60 sec. Charge Current: 0.5mA
Rated Voltage (VDC)		Test Voltage: Rated Voltage Testing Time: 1 to 5 sec. Charge Current: 1mA
Insulation Resistance (I.R.)		Charge Current: 1 minute 10M ohm min

EMI Filter TCPWC - Mechanical Performance Test

Test Items	Specifications	Test Conditions / Test Methods
Component Adhesion (push Test)	Base: 0805 ≥ 2 Lbs Cover: 0805 ≥ 1 Lbs Base: 1206 ≥ 4 Lbs Cover: 1206 ≥ 2 Lbs	The component should be soldered (232°C±5°C for 10 sec.) totinned copper substrate. Applied force gauge to the side of component It must withstand force of 2 or 4 pounds without failure of the component.
Drop Test	Component should not be damaged	Dropping chip by each side and corner. Drop 10 times in total Drop height:100cm Drop weight:125g
Solderability Test	The terminal should at least be 90% covered with solder	The component shall be dipped in a melted solder bath at 235°C±5°C for 5 seconds.
Vibration Test (Low Frequency)	Component should not be damaged	1. Amplitude: 1.5 m/m 2. Frequency: 10-55-10 Hz(1min) 3. Direction: X, Y, Z 4. Duration: 2 Hrs/X, Y, Z

EMI Filter TCPWC - Climatic Test

Test Items	Specifications	Test Conditions / Test Methods
Low Temperature Storage Test	Impedance change: Within±20% Without distinct damage in ppearance.	1. Temp: -40°C±C2°C 2. Time: 1000±48 Hours 3. Component should be tested after 1 hour at room temperature.
Thermal Shock Test		Total: 5 Cycles
High Temperature Storage Test		1. Temp: 85°C±2°C 2. Time: 1000±48 Hours 3. Component should be tested after 1 hour at room temperature.
Humidity Test		1. Temp: 40°C±2°C 2. R.H.: 90%~95% 3. Time: 48±2 Hours
High Temperature Load Life Test	There should be no evidence of short or open circuit	1. Temp: 85°C±2°C 2. Time: 96±12 Hours 3. Load: Allowed DC Current
Low Temperature Load Life Test	There should be no evidence of short or open circuit	1. Temp: -40°C±2°C 2. Time: 96±12 Hours 3. Load: Allowed DC Current

Storage Temperature: 25?°C; Humidity:<80%RH

How to Order - SMD EMI Filters Common Mode Choke TCPWC

TCPWC

900

SMD EMI Filters
Common Mode Choke

Shielding Type
H	Shielding

Dimensions (L×W) (mm)
05	(2.10×1.20) (EIA0805)
06	(3.20×1.60) (EIA1206)

Impedance Tolerance
M	±20%

Packaging
T	Taping Reel
P	Bulk

Impedance
900	90Ω
121	120Ω
102	1000Ω
222	2200Ω