|
| 包装数量 (单位: pcs) |
| 规格 | 内衬塑带 |
| LRC12 | 2,000 |
| 内衬塑带规格 (单位: mm) |
 |
| 阻值 (mΩ) | A | B | W | E | F | P0 | P1 | P2 | ΦD0 | T |
| 0.50 | 3.40±0.1 | 6.70±0.1 | 12.0±0.1 | 1.75±0.1 | 5.5±0.05 | 4.0±0.05 | 4.00±0.1 | 2.0±0.05 | 1.50+0.1 | 1.40±0.1 |
| 0.75 | 3.50±0.1 | 6.80±0.2 | 12.0±0.1 | 1.75±0.1 | 5.5±0.05 | 4.0±0.05 | 4.00±0.1 | 2.0±0.05 | 1.50+0.1 | 1.35±0.1 |
| 1~20 | 3.40±0.1 | 6.70±0.1 | 12.0±0.1 | 1.75±0.1 | 5.5±0.05 | 4.0±0.05 | 4.00±0.1 | 2.0±0.05 | 1.50+0.1 | 0.80±0.1 |
| Notice:
1.The cumulative tolerance of 10 sprocket hole pitch is ±0.2mm.
2.Carrier camber shall be not more than 1mm per 100mm through a length of 250mm. 3.A & B measured 0.3mm from the bottom of the packet. 4.t measured at a point on the inside bottom of the packet to the top surface of the carrier. 5.Pocket position relative to sprocket hole is measured as the true position of the pocket and not the pocket hole. |
| 环境测试 |
| 项目 | 标准 | 测试方法 | |
| Black coating | Green coating | ||
| 温度系数 | 视规格而定 |
MIL-STD-202 条件 304 +25/-30/+25/+130/+25°C。 |
|
| 耐热性 | ±0.5%+0.5mΩ |
±1% |
MIL-STD-202 条件 107G -55°C~150°C，100 次循环 。 |
| 短时间过负载 | ±0.5%+0.5mΩ |
±1% |
JIS-C-5202-5.5 RCWV*2.5 or 最大过负荷电压 5 seconds。 |
| 耐乾旱性 | ±1%+0.5mΩ |
±1% |
JIS-C-5202-7.2 96 小时 @ +125°C 无负载状况下。 |
| 负载寿命 | ±1%+0.5mΩ |
±1% |
MIL-STD-202 M108 RCWV，70°C，1.5 小时开，0.5 小时关 1000~1048 小时。 |
| 耐焊温度 | ±0.5%+0.5mΩ |
±1% |
MIL-STD-202F 条件 210E 260±5°C，10±1second。 |
| 焊接性 | 95%min coverage |
MIL-STD-202F 条件 210E 260±5°C，2±0.5second。 |
|
| Remark: 储存温度： 25±3°C；湿度：< 80%RH |
| 如何订购 |
| LRC | 12 | J | T | E | S | R003 | G | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
|
|
|
|
|
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| To Top Page |
| Page: 1 / 2 |
| 德键电子工业股份公司 台湾电话﹕+886-2-29810109﹔传真﹕+886-2-29887487 大陆电话﹕+86-755-26055363﹔传真﹕+86-755-26055365 |